CAMPFIRE RINGS 120 www . b j s p a r k .com · 1-800- 3 9 2 - 6 1 5 8 STAINLESS STEEL CAMPFIRE RING - FSWS & FXS Series • The FSWS Series Campfire Ring is rolled using 11 ga. (1/8” thick) stainless steel with a 1” roll formed top flange for additional strength and safety. Draft holes are provided for ventilation. The ring is not painted. • The FSWS firering is available in five side heights. See chart below. • Standard: 300 sq. inch single level swivel cooking grate, will move 180 degrees – from over the fire to completely out of the firering – for easy fire building and serving. The handle is never over the fire. Some installation required. • The two tallest firerings with this swivel grate meet the ADA guidelines for reach and operability: one hand operation requiring less than 5 lbs. of force to move. The ring must be filled with aggregate (not included) about 9" deep to provide the elevated fire surface. • Swivel cooking grate is a single welded component using ½-inch dia. black steel bars, mounted on a 2-3/8-inch OD steel tube allowing it to swivel 180 degrees. 5/8-inch dia. operator handle includes a 1/8-in. x ½-in. flat bar coiled grip. All grate bars are welded on both sides. Cooking grate components are finished with high temp, non-toxic black enamel paint. • Standard: three black pin anchors (PA) to secure firering on site, into concrete footings (ring does not tip up). • Optional: three black bolt on spade anchors to secure ring on site, buried in ground (ring does not tip up). See Page 125. • Optional: Model S5 black bolt-on utility shelf. See Page 124. • Optional: FXS Series stainless steel ring only, no cooking grate. Model FSWS-30/7/PA stainless steel campfire ring with Model S5 Shelf. Model FXS-30/7/PA stainless steel campfire ring only, no grate. Model FSWS-30/7/PA stainless steel campfire ring with Model S5 Shelf. Swivel grate is turned out of ring. Model I-RS removable cooking grate. REMOVABLE COOKING GRATE - Model I-RS Model Inside/ Outside Diameter (inches) Side Height (inches) Wheelchair Accessible Height Anchor System Optional: No cooking grate Order this Model # FSWS-30/7/PA 30/32 7-1/4" No PA (Standard) AL(Optional) See Page 125 300 FXS-30/7/PA FSWS-30/9/PA 8-7/8" FXS-30/9/PA FSWS-30/11/PA 11-1/4" FXS-30/11/PA FSWS-30/18/PA 16-3/4" FXS-30/18/PA FSWS-30/24/PA 23-1/4" FXS-30/24/PA Yes Swivel Grate Cooking Area (Sq. In.) Optional: Model I-RS single level removable cooking grate can be used with the FXS Series stainless steel campfire rings. This single-level tip-over cooking grate provides 290 sq. inches of surface area. It can lay flat over the fire or be tipped over and out of the firering. The hinge/pivot bracket is bolted to the inside of the firering. When you don’t need the cooking grate it can easily be removed from the hinge/pivot bracket. The cooking grate is a single welded component using a 5/8" dia. steel perimeter, ½-inch dia. steel grate bars and a 3/4" dia. handle bar. The handle bar also supports the cooking grate on the firering top flange. All grate bars are welded on both sides. The operator handle includes two 1/8"x 1/2" flat bar coiled grips. All grate kit components are finished with high temperature non-toxic black enamel paint. Some assembly is required to attach the cooking grate hinge/pivot brackets to the firering inside wall. Fasteners are included. • • • • •
RkJQdWJsaXNoZXIy NTkzMzk=